Inverter Tutorial with Virtuoso

Authors: Jeannette Djigbenou, Meenatchi Jagasivamani, Jos Sulistyo

This tutorial shows layout of a CMOS inverter. At this point, you should have set up the environment. Otherwise, refer to Setting UP Your Unix Environment. You are assumed to know how to use layout editor, Virtuoso. If you don't know the layout editor, follow the on-line tutorial in the cdsdoc. To start up open book, type cdsdoc & from a terminal. The tutorial for Virtuoso can be found in cdsdoc at: Custom IC Layout -> Layout -> Cell Design Tutorial -> Chapter 2.

The tutorial given below is for the NCSU design kits:

TSMC 0.25um (MOSIS deep submicron rule) of NCSU kit (NCSU_TechLib_TSMC03d)

TSMC 0.25um (MOSIS deep-submicron rule) of NCSU Kit

Creating a New Cellview:

Create a new cellview under an existing library. See Schematic Entry with Composer to find out how to create a new library.

In the Command Interface Window (CIW):

Select File -> New -> Cellview.
Choose the library under which you would like to create the new cell view.
Enter Cell Name: My_Inv (for the tutorial)
Choose Virtuoso as the Tool. View name should be layout.
Click OK.
A blank virtuoso window should open.

Setting Display Parameters:

1. Options -> Display.
2. Set the following options:

Pin names: On
Minor Spacing : 1.08
Major Spacing : 4.32
X Snap Spacing: 0.06
Y Snap Spacing: 0.06
Display levels:
From: 0
To: 30

3. Click "Save To" to set them permanently.

Layout an Inverter:

1. You should follow MOSIS SCN5M_DEEP design rule for TSMC 0.25 um five-metal, 2.5V processing (lambda = 0.12 um & min. length = 0.24 um).

2. The inverter consists of three parts -- p-transistor, n-transistor, and connections.

3. This inverter is probably almost minimum size; therefore, the n- and p-transistors have the same W/L.

Use this figure as a guideline as you go through the procedure.

4. Layout of P-transistor with L=0.24 um and W=0.48 um.

In this tutorial, we are using the Nwell process. Thus, the substrate will be p-substrate. We will create a pmos transistor first. To do that we need an Nwell in which the pmos transistor will be formed.

Draw the well

a) Select the n-well layer from the LSW window
b) Select the Create->Rectangle (or choose the Rectangle icon from the side toolbar).
c) Using your mouse, draw the n-well on the cellview to be 2.94 wide by 2.52 tall .

Draw the p- and n-select regions for the p transistor

a) Select the pselect layer from the LSW window; we will draw the pselect enclosing the transistor
b) Select the Create->Rectangle (or choose the Rectangle icon from the side toolbar).
c) Using your mouse, draw the pselect on the cellview; 1.98 wide and 0.96 tall; its left- and right-edges should be 0.48 away from well edges.
The pselect should be placed within the n-well, even if the size should vary. (you can use the Edit->move command to move the layer)

Draw Diffusions

a) Select the pactive layer from the LSW window; we will draw the active region of the p-device
b) Select the Create->Rectangle (or choose the Rectangle icon from the side toolbar).
c) Using your mouse, draw the pactive on the cellview to be 1.5 wide by 0.48 tall - it should be enclosed by the pselect by 0.24 and by the nwell by at least 0.72

Draw Poly

a) Select the poly layer from the LSW window
b) Select the Create->Rectangle (or choose the Rectangle icon from the side toolbar).
c) Using your mouse, draw the poly on the cellview to be 0.24 long by 1.32 wide.
The poly should be placed at the center of the p-island. The poly should extend over the p-island by 0.30 um.

Place Contacts

a) Select the contact layer from the LSW window
b) Select the Create->Rectangle (or choose the Rectangle icon from the side toolbar).
c) Using your mouse, draw the contact on the cellview to be 0.24 long by 0.24 wide.
The contact should be placed at both sides of the pactive. Repeat the above process for the second contact.

Layout of N-transistor with L=0.24 um and W=0.48 um.

Draw the nselect

a) Select the nselect layer from the LSW window
b) Select the Create->Rectangle (or choose the Rectangle icon from the side toolbar).
c) Using your mouse, draw the nselect on the cellview to be 1.98 wide by 0.92 tall

Draw the N active region

a) Select the nactive layer from the LSW window
b) Select the Create->Rectangle (or choose the Rectangle icon from the side toolbar).
c) Using your mouse, draw the nactive on the cellview to be 1.50 wide by 0.48 tall; it should be enclosed by the nselect by 0.24 around its edges. Also, it needs to be at least 0.72 away from the n-well (= 6 x lambda; MOSIS rule 2.3 for DEEP).

Extend Poly

a) Extend the poly layer created for the p-transistor over the n-island, making sure that the poly extension over n-island is 0.30. (you can use the Edit->Stretch command to stretch the poly)
The poly should be placed at the center of the n-island.

Place Contacts

a) Select the contact layer from the LSW window
b) Select the Create->Rectangle (or choose the Rectangle icon from the side toolbar).
c) Using your mouse, draw the contact on the cellview to be 0.24 long by 0.24 wide.
The contact should be placed at both sides of the p-island. Repeat the above process for the second contact.

Layout necessary connections

Draw the well-contact

a) Select the nselect layer from the LSW window; we will draw the nselect enclosing the substrate (vdd) contact for the P transistor.
b) Select the Create->Rectangle (or choose the Rectangle icon from the side toolbar).
c) Using the mouse, draw the nselect on the cellview; at least 0.96 tall and wide, as it will have to enclose the contact n-active by at least 0.24, which in turn enclose the contact by at least 0.12.
The nselect abuts directly to the pselect of the P transistor, but they should not overlap. Also, both selects should be placed within the n-well.
d) Select the nactive layer from the LSW window; we will draw the body contact region of the p device.
e) Select the Create->Rectangle (or choose the Rectangle icon from the side toolbar).
f) Using your mouse, draw the nactive on the cellview to be at least 0.48 wide by 0.48 tall
g) Add a contact in the center of the well-contact island.

Draw the Substrate-contact

a) Select the pselect layer from the LSW window; we will draw the nselect enclosing the substrate (vss = ground) contact for the N transistor
b) Select the Create->Rectangle (or choose the Rectangle icon from the side toolbar).
c) Using the mouse, draw the pselect on the cellview; at least 0.96 tall and wide, as it will have to enclose the contact p-active by at least 0.24, which in turn enclose the contact by at least 0.12.
The nselect abuts directly to the nselect of the N transistor, but they should not overlap.
d) Select the pactive layer from the LSW window
e) Select the Create->Rectangle (or choose the Rectangle icon from the side toolbar).
f) Using your mouse, draw the n-island on the cellview to be 0.48 wide by 0.48 tall; it must be enclosed by the pselect by 0.24.
The p-island should be placed at least 0.48 um (= 4 x lambda, MOSIS rule 2.5 DEEP) below the n-transistor.
g) Add contacts in the center of the substrate-contact island.

Metal Connections

a) Connect the source of p-transistor to the well-contact using the metal 1 layer.
b) Connect the source of n-transistor to the substrate-contact using the metal 1 layer.
c) Add a contact to the gate (poly)

At this point, your layout should look something like this.

Add Pins:

You need to add pins for the input (named ip), output (named op), vdd, and vss in order to pass DRC. Go to the Creating I/O Pins section to get the procedure on how to add pins to your layout.